| Customization: | Available |
|---|---|
| Standard: | ASTM, AISI, DIN |
| Certification: | ISO |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Introduction INCOLOY alloys belong to the category of super-austenitic stainless steel alloys. Nickel, chromium and iron are the principal constituents of this alloy. By adding different additives this alloy can be made to resist different chemical reagents. Good strength and resistance to corrosion are characteristics of these alloys. Additives such as molybdenum and nitrogen are added to the alloy in order to increase its resistance to pitting, crevice corrosion and thermal stability. The nickel and chromium content extend the corrosion resistance of this alloy over a wide range of environments like non-oxidizing acids, aqueous, caustic chlorides, halides and pulp-mill bleaches. This alloy is available in the form of bars, billets, sheets, round, plate, strips and wire. This datasheet will look into the chemical composition, properties and applications of INCOLOY 25-6MO. Chemical Composition The chemical composition of INCOLOY alloy 25-6MO is given in the following table.ElementContent (%)
Physical Properties The following table discusses the physical properties of INCOLOY alloy 25-6MO.PropertiesMetricImperial
Mechanical Properties The mechanical properties of INCOLOY alloy 25-6MO are tabulated below.PropertiesMetricImperial
Other Designations Some of the designations used to denote INCOLOY alloy 25-6MO are listed below:- UNS N08926 Fabrication Machinability Machining characteristics of this INCOLOY alloy 25-6MO is similar to that of other austenitic alloys. Machining of INCOLOY alloy 25-6MO should be done at a slightly lower speed when compared stainless steel using rigid tooling and optimum lubrication and cooling. Welding INCOLOY alloy 25-6MO can be welded by gas metal arc welding, gas tungsten arc welding, shielded arc welding, plasma arc welding and submerged metal arc welding. The filler metal and electrodes are usually made of INCONEL alloy. Hot working INCOLOY alloy 25-6MO can be hot worked at temperature ranges of 980-1150°C (1800-2100°F). Cold Working Cold rolling may be done on the alloy after annealing. Annealing INCOLOY alloy 25-6MO should be annealed at temperatures greater than 1175°C (2150°F). Applications The INCOLOY alloy 25-6MO is used in the following applications: Chemical and food processing Paper bleaching plants Marine and offshore platform equipment Air pollution control systems Salt plant evaporators Condenser tubes, service water pipes and feed water heaters. |
| Form | Specification | Supply Form | Others |
| Sheet | Thickness:0.40-4.75mm,General Width:1000,1219,1500mm | Whole Coil or piece of it | Cold Annealed,Surface 2B,2E |
| Plate | Thickness:4.76-60mm,Width:1500,2000,2500mm,Length:3000,6000,8000,8500mm(Under 10mm plate can be coiled) | Whole Coil or piece of it | Single hot rolling,Solid solution annealed state,Surface 1D |
| Belt | Thickness:0.10-3.0mm,Width:50-500mm | Whole Coil or Specified size | Cold Annealed,Surface 2B,2E |
| Bar & Rod | Rolled barΦ5-45mm,Length≤1500mm | Polished Bar(circle,Square) | Solution annealing,descaling |
| Forged barΦ26-245mm,Length≤4000mm | |||
| Weld tube | Outer diameterΦ4.76-135mm,Wall Thickness0.25-4.00mm,Length:≤35000 mm | Base on your requirement | Use for PHE |
| Seamless Tube | Outer diameterΦ3-114mm,Wall Thickness0.2-4.5mm | Base on your requirement | Use for PHE |
| Wire | Outer diameterΦ0.1-13mm | Base on your requirement | Ni & Ni alloy, Ti & Ti alloy |
| Forged piece | roundness and square alloy | Base on your requirement | Steel, Alloy |
| Flangs | All kinds of Flangs | Base on your requirement | Steel, Alloy |
| Welding Material | Coil wire Φ0.90mm/1.2mm/1.6mm | Base on your requirement | Certificate of Origin:America, Sweden, Britain, Germany, Austria, Italy, France. |
| Straight WireΦ1.2mm/1.6mm/2.4mm/3.2mm/4.0mm | |||
| Welding rodΦ2.4mm/3.2mm/4.0mm | |||
| Tube | Elbow, three links, four links, different diameter size | Base on your requirement | Ni & Ni alloy, Ti & Ti alloy |
| Explosive bonded laminate | Raw Sheet Thickness≥2mm | Base on your requirement | Ni & Ni alloy, Ti & Ti alloy |
){kind=link}