| Customization: | Available |
|---|---|
| Type: | N08810 / Incoloy 800h |
| Standard: | ASTM, AISI, GB, JIS, DIN, EN |
|
Still deciding? Get samples of US$ 100/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Super alloy VLX800H is a slightly modified version of Incoloy 800 with the 800H grade possessing higher creep and rupture strength. This modification is possible because of the closely controlled carbon content and modified heat treatment.
The following sections will discuss in detail about super alloy VLX800H.
The chemical composition of super alloy VLX800H is outlined in the following table.
| Element | Content (%) |
|---|---|
| Nickel, Ni | 30 - 35 |
| Chromium, Cr | 19 - 23 |
| Manganese, Mn | 1.5 max |
| Silicon, Si | 1 max |
| Copper, Cu | 0.75 max |
| Aluminum, Al | 0.15 - 0.6 |
| Titanium, Ti | 0.15 - 0.6 |
| Carbon, C | 0.05 - 0.1 |
| Sulfur, S | 0.015 max |
| Iron, Fe | Remainder |
The physical properties of super alloy VLX800H are tabulated below.
| Properties | Metric | Imperial |
|---|---|---|
| Density | 7.9 g/cm3 | 0.287 lb/in3 |
| Melting point | 1371°C | 2500°F |
Equivalent materials to super alloy VLX800H are provided below:
Super alloy VLX800H can be machined using the common processes applied to iron based alloys. This alloy does work-harden during machining and displays higher strength and "gumminess" unlike steels. It is recommended that heavy duty machining equipment and tooling should be used to reduce chatter or work-hardening of the alloy.
Any commercial coolants can be used during the machining operations; however water-based coolants are recommended for high-speed operations such as milling, turning, or grinding. Similarly, heavy lubricants are ideal for tapping, broaching, drilling, or boring.
Super alloy VLX800H can be formed using any of the conventional methods as it is very ductile. Powerful equipment is required to perform forming operations as this alloy is strong. It is recommended that heavy-duty lubricants be used while performing cold forming. It is important to clean all traces of lubricant after forming.
Welding of super alloy VLX800H can be performed using all the traditional welding methods. Matching alloy filler metal should be used. In case that is not available, it is advised that the nearest alloy closest to the chemical composition be used. The weld beads should be slightly convex, and preheating is not required. Surfaces to be welded have to be clean and free from oil, paint or crayon marking.
Forging should be performed in the temperature range of 1204-982°C (2200-1800°F).
Hot working can be performed in the temperature range of 1204-871°C (2200-1600°F).
Super alloy VLX800H can be cold formed using all the standard tools except for plain carbon tool steels as they produce galling.
Super alloy VLX800H can be annealed at 1176°C (2150°F) and then air cooled.
Super alloy VLX800H is used in the following application areas:
Stock
|
Form |
Specification |
Supply Form |
Others |
|
Sheet |
Thickness:0.40-4.75mm,General Width:1000,1219,1500mm |
Whole Coil or piece of it |
Cold Annealed,Surface 2B,2E |
|
Plate |
Thickness:4.76-60mm,Width:1500,2000,2500mm,Length:3000,6000,8000,8500mm(Under 10mm plate can be coiled) |
Whole Coil or piece of it |
Single hot rolling,Solid solution annealed state,Surface 1D |
|
Belt |
Thickness:0.10-3.0mm,Width:50-500mm |
Whole Coil or Specified size |
Cold Annealed,Surface 2B,2E |
|
Bar & Rod |
Rolled barΦ5-45mm,Length≤1500mm |
Polished Bar(circle,Square) |
Solution annealing,descaling |
|
Forged barΦ26-245mm,Length≤4000mm |
|||
|
Weld tube |
Outer diameterΦ4.76-135mm,Wall Thickness0.25-4.00mm,Length:≤35000 mm |
Base on your requirement |
Use for PHE |
|
Seamless Tube |
Outer diameterΦ3-114mm,Wall Thickness0.2-4.5mm |
Base on your requirement |
Use for PHE |
|
Wire |
Outer diameterΦ0.1-13mm |
Base on your requirement |
Ni & Ni alloy, Ti & Ti alloy |
|
Forged piece |
roundness and square alloy |
Base on your requirement |
Steel, Alloy |
|
Flangs |
All kinds of Flangs |
Base on your requirement |
Steel, Alloy |
|
Welding Material |
Coil wire Φ0.90mm/1.2mm/1.6mm |
Base on your requirement |
Certificate of Origin:America, Sweden, Britain, Germany, Austria, Italy, France. |
|
Straight WireΦ1.2mm/1.6mm/2.4mm/3.2mm/4.0mm |
|||
|
Welding rodΦ2.4mm/3.2mm/4.0mm |
|||
|
Tube |
Elbow, three links, four links, different diameter size |
Base on your requirement |
Ni & Ni alloy, Ti & Ti alloy |
|
Explosive bonded laminate |
Raw Sheet Thickness≥2mm |
Base on your requirement |
Ni & Ni alloy, Ti & Ti alloy |
4. Contact us
Name: Denny Cheng
Direct line: 021-67897611
){kind=link}