A2 Tool Steel Plate Used in Thermosetting Plastic Molds and Overall Hardened Molds.

• Customization: Available
• Type: Steel Plate
• Standard: ASTM, AISI, GB, JIS, DIN, BS
• Model NO.: A2 Tool Steel Plate
• Surface Treatment: Blackface
• Technique: Hot Rolled
• Application: Mold & Dies, Mold & Dies, Plastic Mould Steel
• Special Use: High-strength Steel Plate, Wear Resistant Steel
• Stock: Stock
• Production Process: Ef/Eaf+Lf+Vd/ESR
• Thickness: 16mm-90mm
• Heat Treatment: Q/T
• Transport Package: Export Standard Packing or Customers′ Demand
• Specification: 20-500mm, or According to customer requirements
• Trademark: BOZHONG
• Origin: China
• Production Capacity: 5000tons/Month

Product Description

A2 Tool Steel Plate used in thermosetting plastic molds and overall hardened molds.

Description
A2 Tool Steel Plate used in thermosetting plastic molds and overall hardened molds.

A2 is American high-toughness wear-resistant tool steel, belonging to wind-hardened steel. The steel carbon has a mass fraction of about 1%, after heat treatment, the hardness can reach 57 ~ 62HRC, and the chromium mass fraction is about 5%. After polishing, the steel surface has a dark gloss, excellent corrosion resistance, and strong ductility. The die cutting edge has good damage resistance. The hardenability of the steel is good, the carbides are evenly distributed, it has a certain impact and good wear resistance. It has good air quenching performance, small dimensional deformation after air quenching, uniform and fine carbides, and good wear resistance.
 

Chemical Composition (%)
Carbon C: 0.95 ~ 1.05
Mould steel
Mould steel

Silicon Si: 0.20 ~ 0.40

Manganese Mn: 0.45 ~ 0.75

Chromium Cr: 4.75 ~ 5.00

Molybdenum Mo: 2.00

Vanadium V: 0.28

Heat treatment
Forging temperature ºC Heat treatment temperature ºC Hardness

1100 ~ 900 Annealing Quenching Tempering Annealing

HB quenching and tempering

HRC

830 ~ 880 1000 ~ 1040 low temperature

180 ~ 200 high temperature

520 ~ 530 <225 60 ~ 62

62 ~ 63

 
Dimensions

Thickness (mm)	Width (mm)	Length (mm)
20-160	2000-2300	3000-5800
47 sets of Vertical Band Saw Strong cutting capacity!!! Monthly 250tons per set We guarantee a prompt delivery time We cut and machine the steel plate as your required sizes P20+Ni is recommended for the Blocks thickness over 450mm

 Excellent characteristics
After properly adjusting the quenching temperature, A2 has higher hardness and impact toughness when tempered at 200 ºC; hardness is higher when tempered at 400 ~ 500 ºC, and the toughness decreases greatly; impact toughness is very high when tempered at 600 ºC The hardness drops significantly.

Precision dies, trimming dies, cold rollers and other tools with complex shapes should adopt low temperature tempering process, so that the working parts of the mold can obtain high hardness, high toughness, good wear resistance and high strength, which can effectively extend the life of the die Excessive wear, deformation, cracking and other early failure phenomena.

Complex molds with large impact load can adopt low quenching and high return process to obtain higher impact toughness and prevent the mold from brittle fracture
Characteristics
Low alloyed Presipitation hardening steel, with good comprehensive mechanical properties, high hardenability, convenient heat treatment, small deformation after heat treatment, good polishability. This material also has good nitriding, electrical machining, welding, and pattern marking performation.
 
Applications
Precision stamping die.

Precision punching die for wire cutting and punching die for various purposes.

Tools for plastic deformation of difficult-to-machine materials.

Die for cold forging, deep drawing and thread rolling.

other

High-speed punching punch and stainless steel punch.

Stretching die, crimping die, embossing die, wearable plastic forming die.

Factory state: HB230-250
Forging Technique

Heat Temperature	Start Forging Temperature	Finish Forging Temperature	Cooling Method
1120-1160°C	1080-1120°C	>=850°C	Air Cooling

 

Tool steel is the steel used to make cutting tools, measuring tools, molds and wear-resistant tools. Tool steel has high hardness and can maintain high hardness and red hardness at high temperature, as well as high wear resistance and appropriate toughness. Tool steel is generally divided into carbon tool steel, alloy tool steel and high-speed tool steel.Tool steel has good wear resistance, that is, the ability to resist wear. The tool can keep its shape and size unchanged under the conditions of considerable pressure and friction.
Process parameters
High-speed tool steel is also an alloy tool steel, which contains C, Mn, Si, Cr, V, W, Mo, Co. And it can be used to make high-speed rotary cutting tools, wear-resistant, high temperature resistant, which is Cr, The ratio of V, W and Mo is relatively large. Take W12Cr4V5Co5 as an example, Cr-> 3.75% -5%, V-> 4.5% -5.25%, W-> 11.75% -13%. The ratio of Cr and V should not be low Less than 3%. The content of P and S shall not exceed 0.030%.

The processing method of alloy tool steel is mainly pressure processing steel and cutting tool steel. There are many types of alloy tool steel, including cold work, hot work, non-magnetic, plastic mold steel, etc. At the same time, the ratio of Cr and V must not be too low. Selection of tool steel for cold work die

The choice of tool steel for cold work molds is based on the main failure mechanism of the mold in practical use. It is not enough to choose tool steel to have only knowledge of steel properties. It must also consider factors such as the number of parts produced, the type of material being processed, thickness, and hardness. A basic method of selecting tool steel is to first eliminate all the failure mechanisms except for wear, and then select the tool steel with the most suitable wear resistance to meet the production requirements.





What we can offer?
 
We offer a wide range of steel products in a wide variety of dimensions and executions, acc.to the common international specifications or customerized.
Machining and heat treatment are available.
Also, we advise you in choosing the right materials.
 
Shape Available
Solid round bar
Flat bar
Square bar
Hexagon bar
Block
Plate
Sheet
Wire rod
Strip

 

	AISI	DIN	JIS	Stock	Application
Hot Work Tool Steel	H11	1.2343	SKD6	√	Die Casting Dies,Extrusion Dies, Hammer Dies, Ram Dies, Forging Dies etc.
	H13	1.2344	SKD61	√
	H10	1.2365	SKD7
	--	1.2367	--
	L6	1.2714 / 1.2713	SKT4	√
	H12	1.2606	SKD62
	H21	1.2581	SKD5	√
Cold Work Tool Steel	D3	1.2080	SKD1	√	Cutting Tools, Punching Tools, Shear Bladers, Reamers, Thread Rolling Dies, Calipers, Sockets etc.
	--	1.2601	~SKD11	√
	D2	1.2379	~SKD11	√
	--	1.2379 MOD	DC53 (Daido)	√
	D6	1.2436	--
	O1	1.2510	SKS3	√
	O2	1.2842	--
	A2	1.2363	SKD12
	S1	1.2550	--
	S7	1.2357	--
	--	1.2767	SKT6
	L2	1.2210	--
Plastic Mould Steel	P20	1.2311	--	√	Mold Base,           Core & Cavity,         Bumper Mold             etc.
	P20+Ni	1.2738	--	√
	P20+S	1.2312	--	√
	--	1.2316	--
	420	1.2083	SUS420J2	√
	--	--	NAK80 (Daido)	√
Alloy Steel	4120	25CrMo4 / 1.7218	SCM420		Shafts, Gears, Drillers, Chains, Bolts, Nuts, Pins, Suds, Keys, Bites, Crankshafts, Connecting Rods, Came, Couplings  etc.
	4135	34CrMo4 / 1.7220	SCM435
	4130	34CrMo4 / 1.7220	SCM430	√
	4140	42CrMo4 /        42CrMoS4 /                1.7225	SCM440	√
	4142	41CrMo4 / 1.7223	SCM440
	4145H	--	--
	4330V	--	--
	4340	34CrNiMo6 / 1.6582	SNCM439
	5115	16MnCr5 / 16MnCrS5 / 1.7131
	5120	20MnCr5 / 20MnCrS5 / 1.7147	SMnC420H
	5140	41Cr4 / 41CrS4 / 1.7035	SCr440	√
	8620	21NiCrMo2 / 1.6523	SNCM220
	8640	40NiCrMo2-2 / 1.6546	SNCM240
	--	18CrNiMo7-6 / 17CrNiMo6 / 1.6587	--
	9840	36CrNiMo4 / 1.6511	--
	E71400	41CrAlMo7-10 / 1.8509	SACM1
	--	34CrAlNi7 / 1.8550	--
Bearing Steel	E52100	100Cr6 / 1.3505	SUJ2	√	Bearing, Shafts etc.
	--	100CrMn6 / 1.3520	--
	--	100CrMo7-3 / 1.3536	--
Spring Steel	5155	55Cr3 / 1.7176	SUP9		Springs
	6150	51CrV4 / 1.8159	SUP10
	9261	60CrSi7 / 1.7108	--
Carbon Steel	1010	CK10 / C10E / 1.1121	S10C		Shafts, Chains, Bolts, Nuts, Pins, Suds, Keys, Bites, Came, Couplings  etc.
	1020	C22 / 1.0402	S20C	√
	1040	CK40 / C40E / 1.1186	S40C	√
	1045	CK45 / C45E / 1.1191	S45C	√
	1050	CK50 / C50E / 1.1206	S50C	√
	1055	CK55 / C55E / 1.1203	S55C
	1064	CK60 / C60E / 1.1221	S58C
High Speed Tool Steel	M2	1.3343	SKH51	√	Reamer,       End-mill,          Hob, Cutter, Bite, Drill, Punch, Tap, Brooch etc.
	M7	1.3348	--
	M42	1.3247	SKH59	√
	M35	1.3243	SKH55	√
	T1	1.3355	SKH2
	T15	1.3202	--
	T42	1.3207	SKH57

 
Note:
1). √ means we have stoc
2). Delivery Condition:
Smelting: EAF+LF+VD (+ESR)
Making: Hot rolled, Cold rolled, Forged, Cold Drawn
Heat Treatment: Untreated, Annealing, N+T, Q+T
Surface: Black, Peeled, Turned, Milled, Grinded, Polished
 
Packing & Shipping
Hot keywords:high quality

Our company